Analysis of several common problems in pressure calibration table calibration:
The device that detects the spring hammer in the pressure calibration table will become a calibration device. Because there is no corresponding calibration procedure, a calibration certificate should be issued, and the calibration certificate should specify the measurement uncertainty. The "measurement standard assessment specification" requires "N-repeat measurement times, N should be as large as possible, generally not less than 10. If the repetitive introduction of the uncertainty component is not the main measurement uncertainty in the verification or calibration results Component, which allows to reduce the number of repeated measurements appropriately, but at least N>=6" should be satisfied. However, the use of the calibration device of the pressure calibration table emphasizes that “the impact element should be turned to different positions after each operation. The average value of the three readings on the calibration device can be used as the actual value of the impact energy of the measured spring hammer.†Therefore, the number of repeated measurements is insufficient.
Domestic and foreign production of the pressure calibration table spring hammer calibration device impact kinetic energy measured value using the dial pointer readings, due to the size of the dial and the diameter of the pointer caused the reading error is too large. There are two reasons for this: (1) Large division values. Because the impact kinetic energy of the spring hammer of the pressure checkbench is very small, it is difficult to achieve a small division value by conducting a small-scale 2J split on the disk by using the principle of potential energy. At present, the PDL company's domestic sales of the pressure calibration table spring hammer calibration device has a division value of 0.02J, scale line spacing of about 1MM, a few companies in the country production of pressure calibration table spring hammer calibration device indexing value 0.01J, tick spacing is less than 1MM. Taking a 0.14J spring impactor as an example, the accuracy of the calibration device is calculated as 3%, and its index value should be 0.004J. It is difficult to achieve the internal subdivision scale line on the 1MM pitch of the dial. (2) The pointer diameter greatly affects the reading. The calibration device manufactured at home and abroad uses a 0.7MM piano wire as a pointer, and the pointer of 0.7MM occupies 2/3 space of 1MM between two scale lines, resulting in a large error in estimation. Even if the scale is subdivided between the marks with a pitch of only 1 mm, the indexing value is increased. However, due to the effect of the 0.7MM indicator, the small value of the indexing is also invalid, and the estimation error is still large.
Through the above analysis, the spring hammer calibration device in the pressure calibration table can not meet the calibration of all the spring hammers. At the same time, there are no uniform calibration standards for the measurement institutions throughout the country, so the calibration methods and calibration devices are different. Therefore, in order to improve product quality and strengthen measurement management, the device has a uniform calibration standard across the country, and it is very important to develop a scientific and effective calibration device for pressure calibration tables.
Leisuwash specializing in manufacture Automatic Car Wash Machine, Touchless Car Wash , Automatic Touchless Car Wash, touchless car wash equipment, robot car wash, smart car wash system, leisuwash 360, leisuwash leibao 360, laserwash 360, leisuwash touchless car wash machine, leisu wash touchless car wash automatic, leisu wash 360 high pressure touchless car wash equipment, robo car wash, touch free car wash, leisuwash 360 touch free car wash, leisuwash 360 price, automatic car wash price, leisuwash in malaysia, no touch automatic car wash machine.
Leisuwash 360 touchless car wash machine high intelligent high quality, with car wash + car care + drying process totally, each car wash takes time 1 minute to 5 minutes which depends on the car wash mode.
The newest LeisuWash inbay Automatic Car Wash raises the standard for Touchless Car Wash Equipment. With Revenue Enhancement and Total Cost of Ownership improvements being the main focus, this vehicle wash system delivers the industry`s best Return on Investment. Smart 360â„¢ Technology enables the car wash system to be responsive to the dynamic conditions in the wash bay and allows it to [think for itself", increasing up-time and optimizing the wash process.
Leisu Wash,Leisuwash 360 Magic,Touchless Car Wash Equipment,Magic 360 Touchless
Hangzhou Leisu Cleaning Equipment Co.,Ltd , https://www.sdtouchlesscarwash.com