1. Requirements for Water Sources When the sprinkler uses a river ditch or a pond as a water source, be careful that all the ends of the suction pipe do not enter the water. In order to avoid inhaling stones or more sand and drift debris, the suction pipe end is generally provided with a filtering device, and it is forbidden to remove the filtering device during the water absorption. If the water source is shallow, it is necessary to dig up the water absorption area in advance so as to ensure that it does not contain impurities and air. The water pump requirements for different sprinklers are different. The clean water pump requires no impurities in the water. The turbid water pump requires no stones and excessive sediment in the water.
2. Before adding water to a centrifugal water pump, a certain amount of water must be added to the water pump. After the water is added, the water inlet must be closed. When the self-priming pump is used for the first time, it is necessary to add water, and it is unnecessary to add water afterwards.
3. The water inlet pipe must be vacuumed when the water inlet pipe system must maintain a certain degree of vacuum in order to suck water into the tank. The inlet pipe system must be sealed reliably, the hose can not be damaged, the hard pipe can not have cracks, otherwise it will have a phenomenon of air leakage, which will result in the situation that it cannot suck water.
4. Parking stalls Sprinklers must be parked either before or after watering.
5. Winter watering Before the advent of winter, the water in the pumps and pipes should be vented to prevent freezing. The northern part of the country is generally no longer under construction during the severe winter. Therefore, after the construction is completed, the water in the pump and the water pipe will be drained immediately to prevent future problems.
6. Sprinkler Precautions The front sprayer of the sprinkler is located at a low position and close to the ground. The spray pressure is greater and can be used for flushing the road surface. The rear nozzle is located at a higher position (the sprinkler head is generally installed on the left and right sides respectively), and the sprinkler surface is wide. When spraying water on highway construction, the front nozzle should be closed when the rear nozzle is used, and the width of the water can be adjusted as needed when using the adjustable nozzle. The wider the sprinkler width, the less the amount of intermediate overlap and the more uniform the sprinkler density.
7. Lubrication and fastening In the course of use, lubrication points of the drive assembly must be regularly lubricated, and the connection points are often tightened to ensure normal use.
8. Periodically, the sewage tank is equipped with a sewage pipe. The entrance of the pipe is the lowest point of the tank. After a period of use, the discharge pipe switch should be opened periodically to remove the accumulated debris from the tank until the water becomes clear.
Automatic Sliding Door Operators
High quality door residential automatic door opener
Carton+Foam+Bubble Bag and Pallet
Safety & Operation Devices of High Speed PVC Roll up Door:
In consideration of operation safety for high speed PVC roll up door, we provide the photo cell, and wireless safety airbag device as the standard safety device; And to enrich the operation methods of the high speed door, various options are provided such as manual button, transmitter, control box, radar sensor and inductive loop device. Different styles of transparent window are also available for better vision view.
Varied Running Speed of High Speed PVC Roll up Door:
Running speed of High Speed PVC Roll up Door is adjustable: Opening speed from 0.80m/s to 2.0m/s, and closing speed from 0.6m/s to 1.0m/s. Running speed adjustment can be achieved through inverter inside the control box, t to meet the actual needs.
Driving System of High Speed PVC Roll up Door:
Driving system is the core part for the high speed roll up doors. For the motors, we can provide multiple options for different demands, brands including SEW, SIEMENS, SNMA, SEJ and Servo Motor; All the motors are provided with manual brake, that offers emergency operation under power failure. Furthermore, motor power can be applied based on the real door size, in supply voltage 220V single phase and 380V three phase.
sliding door operators, automatic door motor opener, door accessory ,automatic door operators,fast door accessory
SHENZHEN HONGFA AUTOMATIC DOOR CO., LTD , http://www.hongfahsrs.com