Other name: Cold roll forming machine, steel tile roll forming machine.
Components of whole line:
1. De-coiler
2. Shearing Device
3. Forming System
4. Cutting device
5. Run-out Table
6. Electrical Sytem
Process flow:
Decoling--Straightening--Forming--Measure Length---Cutting-- Run-out table
Technological Parameters:
1. Hydraulic Un-coiler
Width of raw material: 1250mm
Max Capacity: 10000kgs
Max out diameter of coil: 1600mm
Inner diameter of coil: 500-600mm
Hydraulic feed and brake
The power of motor: 5.5kw
2. Shearing Device
Shearing way: Manual
The material of blade: Cr12 with Heat treatment HRC60-62
3. Main Forming System
Feeding width: 1219mm
Product width: 1000mm
Height of waves: 37mm
Thickness of sheet: 0.35-0.6mm
Material: GI sheet coil or Colored sheet coil
Roller stations: 18 rows
Material of Roller: C45 steel
Surface of Roller: Chrome plating
Diameter of main shaft: 80mm C45steel, modulation
Main Bearings: 60211
Power of main motor: 5.5kw Servo motor
Forming Speed: 0-15m/min
4. Cutting device
Oil pump station 1set
Motor power of Oil pump station: 4kw
Forced air cooling device available
Cutting mould: 1set
Material of blade: CR12 with heat treatment HRC60-62
Pressure of cutting: 15tons
5. Run-out Table
Frame: Angle bar or steel tube welded
Length: 3m
Quantity: 1 PC
6. Electrical System
PLC and HMI touch Screen
Automatic length measurement
Automatic quantity measurement
Length measurement: Rotary Encoder
Over current protection for control system, aviation plugs
Cutting off type: Paused to cut, moving automatically after cutting.
Power: 380V 50Hz (as per your request)
We also can design and manufacture as per your request!
Contace Person: Jacky (sales manager)
Mobile: +86-15503170286
| Advantage of our roll forming machine |
| High quality |
| Lower cost |
| Durableness |
| High efficiency |
| Reliable working |
| Low failure rate |
| Low energy consumption |
| Trouble free after sales service |
Precautions for daily maintenance of hydraulic cylinders
1. Regularly inspect the sealing components of the hydraulic cylinder, such as O-rings and gaskets, to ensure that they are intact and undamaged. If there is wear or aging, they should be replaced in a timely manner.
2. Regularly check the liquid level of the hydraulic cylinder and keep it within the specified range. If the liquid level is too low, add hydraulic oil in a timely manner.
3. Regularly inspect the connection parts of the hydraulic cylinder, such as oil pipes and joints, to ensure their tightness and reliability. If there is any looseness, it should be tightened in a timely manner.
4. Regularly clean the outer surface of the hydraulic cylinder to prevent dust, sand, and other debris from entering the interior of the cylinder and affecting its normal operation.
5. Regularly inspect the surface of the piston rod of the hydraulic cylinder, and promptly repair or replace it if there are scratches or wear.
6. Regularly inspect the hydraulic system of the hydraulic cylinder, and promptly handle any problems such as oil leakage or unstable pressure.
7. When the hydraulic cylinder is not in use for a long time, its hydraulic oil should be drained to avoid oil aging, deterioration, and affecting the normal operation of the hydraulic system.
8. When repairing or replacing hydraulic cylinders, attention should be paid to safety to avoid sudden movement or pressure release of the hydraulic cylinder, which may cause personal injury or equipment damage.
For Liugong Cylinder Seal Kit,For Liugong Swing Motor Seal Kit,Center Joint Seal Kit For Liugong,Center Joint Seal Kit Liugong
Safe Seal Technology Co., Ltd. , http://www.aprseal.com