Some of the transport of dangerous goods in life, such as oil derivatives, requires tankers to operate. We can see tankers driving on the streets whether it is wind or rain. Everyone knows that thunderstorm weather is very dangerous. In order to reduce the danger, it is necessary to be cautious when driving a tanker in thunderstorms. Then what are the precautions for driving a tanker in thunderstorms? Let's take a look!
1ã€Thunderstorm driving tanker must pay attention to low-speed driving, keep distance with other vehicles, and extend the safety distance. Due to slippery roads on rainy days, emergency braking should be avoided to make the body skid and side-to-side vehicle side collisions. If the speed is too fast and the distance from the vehicle in front is too small, the sprayed water mist may affect the driver's line of sight. In an emergency, there is a rear-end collision with the preceding vehicle.
2. Drivers of thunderstorm driving tanker must concentrate and do not look around. Hold the steering wheel with both hands. Do not be attracted by the splashes around the car and distract the vehicle from the driving route. In the rainy days, we must remember to open the wipers, so that we can clear the rainwater on the windshield in time so that the driver can better see the road conditions and greatly reduce the chance of accidents.
3. Sometimes, thunderstorm weather will produce water on the road. At this time, the driver must not blindly pass through it. It is necessary to determine the depth of the accumulated water and make timely judgments before passing it. When the water depth is below the bumper or less than half of the wheel, it can pass. Pay attention to low-speed driving during driving. Do not shift gears or turn sharply. Do not turn off the vehicle, otherwise it is easy to make the exhaust pipe of the vehicle damage the engine. . If the depth of stagnant water cannot be estimated, do not take risks and wait for the water to recede or detour.
4, thunderstorm weather vehicles will be more likely to slip phenomenon, this time the driver must not panic, to calm some. Hold the steering wheel firmly to prevent the vehicle from leaving the track. If the front wheel slips, you need to turn the steering wheel in the opposite direction. If the rear wheel slips, you will drive the steering wheel in the same direction.
Experienced tanker drivers will be able to deal with thunderstorms easily, while novice drivers will be very nervous. Have you seen the introduction in the text feel that there is a spectrum of mind? Keeping these points in mind allows you to drive the tanker in thunderstorms with confidence.
PTA Powder
Main application:Repair and strengthen workpiece surface, significantly
Welding method:PTA welding
Main equipment:PTA welding machine
Flame core temperature: about 10000℃
Technological characteristics:PTA has high temperature, concentrated energy, stable combustion, small heat affected zone, fast welding speed, high production efficiency, easy to obtain low dilution rate of surfacing layer, surfacing layer and workpiece matrix are metallurgical bonding,, bonding strength is high.
PTA welding technology is one of surface strengthening methods, which has high deposition rate, low dilution rate, and could be applied with many kinds of powder. The manufacturing craft of PTA powder is normally gas atomization, which reduces satellite of powder. We supply 4 main categories of PTA powder: Nickel-based alloy powder, Iron-based alloy powder, Cobalt-based alloy powder and Mixed Powder.
Nickel Based Alloy Powder possesses high temperature resistance and wear resistance, it is the most popular alloy powder applied by PTA welding both domestically and internationally. Coating hardness is within the range of HRC 30-60. It could be applied to various industries like agriculture, plastic, paper, marine and steel making where wear and corrosion protection needed. Some examples are plunger, moulds, pump leaf and screw.
Iron Based Alloy Powder is more widely used and a more economic choice. With high abrasive resistance, it is more commonly applied to mining tools, drilling tools and mixers of iron and steel making industry, coal industry, shaft, oil and energy industry.
Cobalt Based Alloy Powder is recommended for corrosion and oxidation resistance, with better hot hardness values than equivalent Nickel based alloy powder. It is widely applied to steel making industry, coal industry and mining industry.
Mixed powder mainly refers to NiCrBSi mixing with other hard-phase powder such as cast tungsten carbide and other cemented alloy powder, which allows the powder better hardness around HRC60 and excellent abrasion resistance.
Mixed powder is more often used for mining equipment for oil sands, lignite, oil drilling tools, excavator buckets, extrusion screws for plastic processing, grain and oil processing, etc.
PTA Powder,Iron Based Alloy Powder,Cobalt Based Alloy Powder,Nickel Based Alloy Powder
Luoyang Golden Egret Geotools Co., Ltd , https://www.xtccarbide.com